Why does my serve go into the net?
Serves usually go into the net because contact is too low: the arm is still bent, the hitting arm isn't high enough, or the ball is hit below your full reach. This page covers contact height and extension; for a serve that simply lacks power, see the no-power guide, and for a general diagnosis, the weak-serve guide.
From one phone video we measure trophy-position knee bend, contact height, arm extension and rhythm.
Why do low serves hit the net?
The lower the contact point, the less room the ball has to clear the net and still come down in the box, so you are forced into a loopier trajectory with less margin.
- Hitting harder or 'down' on the ball from a low contact point usually makes it worse.
- Raising contact gives you more margin without changing anything else.
What causes low contact on the serve?
Symptom → what we look at → cause → drill.
- Ball hit below your reach → contact height against standing height (flag under about 1.15 ×) → low contact → Toss placement (2 × 15).
- Arm still bent at impact → elbow bend at contact (flag above about 45°) → bent arm → High-point reach (3 × 8).
- Ball hit beside the head → how high the hitting arm is raised (flag under about 70°, 'possible' only) → low arm → Wall shadow serve (2 × 10).
What else makes serves go into the net?
- A toss that drifts too far forward: toss placement is not measured, but it usually shows up as low contact.
- Pulling the head and chest down early: watch your contact frame on the overlay.
- Racket-face angle at contact is not measured, because the racket is not tracked.
How do I check my contact height?
- Film one serve from the side or behind, landscape, with the racket above your head in frame and sound on.
- Upload it: the report shows your contact frame with height, elbow and arm values, and ranks the fix.
- Free on the web with no account: a few free analyses per day.
What a single phone video can and can’t measure
The honest scope of 2D pose analysis from one camera.
| What | From one phone video |
|---|---|
| Joint angles in the camera plane: elbow, knee bend, trunk tilt | Measured |
| Contact point relative to the front hip (side-on view) | Measured |
| Order and timing of hip, shoulder and arm movement | Measured |
| Serve trophy position, arm extension and contact height | Measured |
| Shoulder turn and hip–shoulder separation (3D rotation) | Estimate only |
| Racket drop: inferred from the wrist path, flagged as “possible” | Estimate only |
| Wrist and forearm rotation (pronation) | Not measured |
| Ball speed, spin and placement | Not measured |
| Grip and racket-face angle | Not measured |
Frequently asked questions
- Should I aim higher over the net?
- Aiming higher helps margin, but the lasting fix is a higher contact point, which lets the ball clear the net and still drop in.
- Do I need more spin to stop netting serves?
- Spin adds margin on second serves, but it doesn't fix a bent arm or a low arm. Raise contact first. Spin is not measured.
- Why do my second serves go into the net more?
- Nerves often shorten the motion, so the arm stays bent and contact drops. Film a set of second serves and compare contact height with your first serve.
Try it on your own swing
Upload a 10–30 second clip and get your priorities in about a minute.
Check my serve for thisSources
The reference values on this page come from these studies. Thresholds are coaching guides, not calibrated limits.
- Jacquier-Bret et al. Kinematics characteristics of key point of interest during tennis serve among tennis players: a systematic review and meta-analysis. Frontiers in Sports and Active Living, 2024. — Elbow flexion at ball impact 30±16 deg
- Baldinger et al. Influence of the Camera Viewing Angle on OpenPose Validity in Motion Analysis. Sensors, 2025. — Shoulder elevation ~100-110 deg at impact; shoulder angles least reliable in 2D